Page 2 of 3
Posted: Mon Mar 20, 2006 6:53 pm
by ninja79
gitarjunky wrote:Yeah, thanks for the support guys, anyone know what a new shift lever and whatever has to happen with the steering (just turns a little too far to the left now) will cost?
Shift leaver costs $66.52. Trust me -- I know
Don't know about the steering. You might want to get it checked out.
Now what did I tell you about the frame sliders?
http://www.motosliders.com/
Oh yeah, welcome to the club.
Posted: Mon Mar 20, 2006 6:58 pm
by Shiv
Ouch, sorry about your off.
The bike is replacable though, you're not. So doctor up those wounds/beaten up parts and then ride off into the sunset.
Stick a Band-Aid over the dent in your tank; good as new.
Posted: Mon Mar 20, 2006 8:23 pm
by Mintbread
Considering the damage to your bike, would a set of frame sliders made an ounce of difference to the outcome?
Posted: Mon Mar 20, 2006 10:24 pm
by pseudopod
I'm curious -- where you riding in the center of the lane or in one of the tire strips? I went down just like you described except I didn't even hit the brake hard at all. I was riding smack in the center though and that's what did it -- all that oily stuff that sits there.
Posted: Tue Mar 21, 2006 4:05 am
by CNF2002
Out of curiosity after a small spill like that how did you get the bike home without a shift lever?
Posted: Tue Mar 21, 2006 4:37 am
by SuperRookie
CNF2002 wrote:Out of curiosity after a small spill like that how did you get the bike home without a shift lever?
My guess is the bike was in gear...
Additionally, dude, don't ride around with jagged, broken-off bits from your bike in your pockets.
I understand the reasoning, but that can be problematic...
Posted: Tue Mar 21, 2006 7:08 am
by gitarjunky
To answer all your questions....I was in the left tire track. I was about to change lanes and was checking my blind spot, there was a car there so I didn't change lanes and then when I turned my head around the car infront of me was stopping. I hit the front brake a little to hard with my front tire every so slightly turned to the left and before I knew what was happening, I was down to that side. I pretty much hit the ground and bouced right back up to my feet.
And my shift knob in my jacket isn't sharp. Its just the rubber knob...it just snapped off the lever. Oh yeah, and this happened like 4 blocks from work so, I pushed it to a side street (talk about embarassing) and then I realized it was probably in gear (2nd or 3rd) and it was so I hopped back on and rode it back to work in one gear. I'm going to transport it to the dealer which is a few blocks away from here the same way later today on my lunch break.
Posted: Tue Mar 21, 2006 7:58 am
by cb360
Glad you are ok - if you have to go down, that's not a bad way to do it. Just learn from it and move on - better a low speed one than a high speed!
Posted: Tue Mar 21, 2006 2:22 pm
by Sev
cb360 wrote:Glad you are ok - if you have to go down, that's not a bad way to do it. Just learn from it and move on - better a low speed one than a high speed!
Speaking from experience I'm inclined to agree.
Posted: Tue Mar 21, 2006 4:49 pm
by gitarjunky
So the bike is going in Thursday morning to get inspected/fixed. Upon inspection in the daylight today, I think I bent the radiator assembly in the front, I need a new shift lever (the linkage seems fine, it still shifts gears smoothly if you just push the lever with your hand) and the steering head needs to be inspected to make sure I didn't mess that up. The headlight and cowl around it are scraped just a little bit, something that can wait to be fixed. I know the radiator assembly is like 450 bucks, and the shift lever is like 70....does anyone know how much labor is going to be? UGH! This stupid little dump is going to cost some big dough....lesson learned....lesson learned....