Total Motorcycle Community Forums

Right you are Karate-chick. The key word you used is feathering.

About the only times I can think of when I feather the clutch is when I'm starting from a dead stop or going slower than my bike can idle in 1st gear, such as approaching a stop light or line of traffic at a stop. If there is no one behind me who looks like they will run into me, I will go very slow, feathering the clutch to keep moving, but not having to stop completely.

I wonder if those who believe they should "ride" the clutch don't understand what is meant. They seem to think that "riding" the clutch means to pull the lever all the way in and coast.

In any case, whenever you disengage the transmission from the engine, you are free-wheeling and while free-wheeling, you have no control over the bike other than steering and braking.

SausageCreature wrote:snip.......

Why would you not? When I want to decelerate at a slower rate, like when a light ahead changes to green and I have to wait for a stopped car to get going, if distance allows I let air resistance slow me down and the engine idle.

I don't see how engine braking can give you any more braking power than your rear brake. I guess if you drop it down a gear or two the engine pulsing might act as a sort of ABS, but under normal conditions why not use your brakes, being as they are specifically designed for the purpose?

Why would you not? Well, when you put your vehicle into "neutral", which is what you are essentially doing when you pull the clutch in, you are taking away any control of your bike, other than braking and steering. So, why not just either shut off the throttle, and if you aren't slowing fast enough, drop a gear or two? That way you are staying within the power band in case you need power to move out of the way quickly (God!! how many times do we have to say this???)

But you are correct in saying that engine braking does not give more braking power than the rear brake, but remember, rear brakes are only 1 source of slowing/stopping. You also have your front brake andengine braking. So, add it up and you come to the logical conclusion that 3 sources of slowing/braking are better than 1, do you not?

Also, another thing about braking.

The front brake is more effective than the rear brake. Why? you ask.

When you apply the front brake, the bike's centre of gravity migrates foreward, the front suspension compresses and this puts more weight on the front wheel, tranferring the weight into increased pounds per inch between your tire and the road surface.

For those of you who believe that you should pull the clutch in and use the brake to slow/stop your bike, I would like you to try the following.

1: Take your bike to a street with next to no traffic.
2: Get up to the speed limit
3: Close your throttle and check to see how long (time, not distance) it takes to drop down to 10 MPH.

Repeat this with the only change being
4: Drop one gear lower and close your throttle again and check the time it takes to drop to 10MPH.

Repeat but do this
4: Pull your clutch lever in all the way and check to see how long it takes to get to 10MPH.

Finally, do this
4: Shift down and use braking at the same time to slow to 10MPH.


We would like you to post your results next time you come here.
Please??

Many good points here. I have never understood how you could ride without downshifting. I've done it since day one. It provide added stability when slowing down to me. I downshift in my car and on my bike. I would only disengage the clutch in emergancy stopping, when there was no real time to downshift safely. Otherwise in almost every case I can think of, I give myself enough time to stop using almost ONLY my engine. My brake lever is for flashing the light for the most part.

jonnythan wrote:

Sevulturus wrote:Why would you want to hold in your clutch while you brake? Unless it's emergency braking where you should be downshifting as fast as you can, while you do it.

I'm I'm riding in 4th gear and see a red light up ahead, I'll usually drop it down to third gear... but not second. Going below 25 or so will make the bike chug in third gear, so instead of quickly downshifting twice (pull clutch, shift, release clutch, pull clutch, shift, release clutch, then pull clutch in while in first gear to stop), I just pull the clutch in and stop with my brakes.

Saves an awful lot of shifting and I see no reason to do it any other way.

I suppose that if you're in a bike where you're in first gear up to 40mph, then it makes sense.

I've done the same thing before myself, usually I double down while I'm shifting to increase my compression braking. But I still try and work my way down to first while I'm rolling and under power. Because if something big comes up behind me at speed I've got power to the engine, and all I need to do is roll the throttle and I'm away.

No dicking about wondering if I'm in the right gear, no need to worry about smoothly releasing the clutch, because I'm already rolling under power.

HungPower wrote:When I used to drive my stickshift car, or even any manual car for that matter, everytime I brake, I would find my self holding in the clutch. If i needed to accelerate or maintain a speed, I would just go up to the friction point and then release. But then I realized that as I started to ride a motorcycle, everytime I brake I would also hold in the clutch and follow the same habits. For example, say if I was to start braking, I'd hold in the clutch as I would brake but if I had to continue on, I would slowly let out the clutch and give it some gas. Now if I still needed to brake harder I would hold in the clutch continuiously and then downshift if necessary. Now just wondering, does anyone else do this or do I need to fix my habit?

I find that I have a controlled Descend when I am not engaging the clutch. For example if I was driving down the freeway at 75 MPH, and want to slow down or stop quickly I would apply the breaks while on the gear without engaging the clutch. When I have slowed to about 10-15 mph, I would then engage the clutch or simply put the gear to neutral and relax.

It also causes the Car to slow a lot quicker due to Engine friction.

Another method I use to slow down quicker is to shift-down as I am breaking. Though it stresses the engine to its limits, clutch acts like some sort of a secondary break; causing the car to slow down a lot faster.


---------------------
This post has been Re-Written Dude to constructive critisism of "ZooTech"

silentx wrote:I find that I get have a controlled Decend when I am not holding the clutch. Ex: my 4 wheeler, If I am on freeway at 75 MPH and wanna slow down/stop quickly. I would apply break while on the gear with no clutch. When am slowed to about 10-15 mph I would then hold the clutch or simple put to nuetral and relax my foot

Also it slows lot quickly due to Engine friction.

Another method I used to slow down faster is I shift down as I am breaking. The clutch act like some what of a break also (again engine friction) but Stresses engine out a bit.

Exactly which country are you from, silentx? I need to know so I can use the proper accent in my head when reading your incoherent ramblings and broken English.

ZooTech wrote:

silentx wrote:I find that I get have a controlled Decend when I am not holding the clutch. Ex: my 4 wheeler, If I am on freeway at 75 MPH and wanna slow down/stop quickly. I would apply break while on the gear with no clutch. When am slowed to about 10-15 mph I would then hold the clutch or simple put to nuetral and relax my foot

Also it slows lot quickly due to Engine friction.

Another method I used to slow down faster is I shift down as I am breaking. The clutch act like some what of a break also (again engine friction) but Stresses engine out a bit.

Exactly which country are you from, silentx? I need to know so I can use the proper accent in my head when reading your incoherent ramblings and broken English.

LOL.. I see.. Let me fix it for you..

Oh the country... don't think you can replicate the my accent. Also I cannot replicate your accent either, simply because your accent is too insulting and some what rude. But thank you for the correction(s) It was pretty bad; I agree. I am sleepy as hell.

silentx wrote:

ZooTech wrote:

silentx wrote:I find that I get have a controlled Decend when I am not holding the clutch. Ex: my 4 wheeler, If I am on freeway at 75 MPH and wanna slow down/stop quickly. I would apply break while on the gear with no clutch. When am slowed to about 10-15 mph I would then hold the clutch or simple put to nuetral and relax my foot

Also it slows lot quickly due to Engine friction.

Another method I used to slow down faster is I shift down as I am breaking. The clutch act like some what of a break also (again engine friction) but Stresses engine out a bit.

Exactly which country are you from, silentx? I need to know so I can use the proper accent in my head when reading your incoherent ramblings and broken English.

LOL.. I see.. Let me fix it for you..

Oh the country... don't think you can replicate the my accent. Also I cannot replicate your accent either, simply because your accent is too insulting and some what rude. But thank you for the correction(s) It was pretty bad; I agree. I am sleepy as hell.

...
Huh?

KarateChick wrote:I've always used engine braking in the car so it seemed normal to do so on the bike - flashing the brake lights in both cases.

A lot of people replying to this thread hinted at the brake lights, but I thought I'd emphasize it. I commute in Silicon Valley, the cell-phone driver capital of the world (you can dispute if you want). It's a good idea to turn on the brake lights the instant you think of braking. A few on this forum suggested feathering the rear brake pedal to illuminate the brake light. My MSF instructor discouraged this behavior for a beginner, as it might train us to rely only on the rear brakes as an instinctive reaction during an emergency. (Whatever we normally do, we'll do in panic.) He suggested using both brakes, and if the bike slows too much from the combination of both brakes and engine compression, then eliminate the engine factor with the clutch from the start of the braking process.

Just a newbie perspective.

scan wrote: ↑Fri Oct 27, 2006 8:01 am Many good points here. I have never understood how you could ride without downshifting. I've done it since day one. It provide added stability when slowing down to me. I downshift in my car and on my bike. I would only disengage the clutch in emergancy stopping, when there was no real time to downshift safely. Otherwise in almost every case I can think of, I give myself enough time to stop using almost ONLY my engine. My brake lever is for flashing the light for the most part.

Then in all honesty, you're just unnecessarily screwing your engine up.

Motorcycle brakes are already over qualified for their purpose (they're almost as strong as car brakes and have to stop a mass that's hardly a quarter of it). But if you still want to use your engine as a brake, you should brake first and drop your revs before you downshift.

So using ONLY the engine to stop is not only unnecessary, it's... umm, let's say... the opposite of smart!

In the words of Keith Code the legend: "Brakes are cheap, engines are expensive".